+1 (888) 290-3215 experts@r2r.tech

Web Width Measurement — Industrial Ethernet — SCU5

Quick Start Guides › Web Width Measurement
Change Selection

Your Sensor

Select your ODC Family model to unlock datasheets, drawings, and 3D models:

ODC 960 — 960 mm sensing range

Not sure which size? Pick the sensor wide enough for your max expected wander + 10% margin. View all ODC Family models

Your Products

Download PDF Download All (ZIP)

ODC 960

SCU5

What You'll Need to Order

QtyItemSKUConnection
1 Quick Disconnect Sensor Cable - 3m (10 ft) U2-01975 sensor.connector → controller.S1
1 24 V DC Input Power Cable, Length 5 m 21218-5m power.output → controller.P1
1 M12 to RJ45S, Shielded Cable - 9.8ft/3m 21222-3m controller.Port3 → plc.input
1 Quick Disconnect Sensor Cable - 3m (10 ft) U2-01975 sensor2.connector → controller.S2

Select cable length based on your installation distance

BOM generated for sensor model: odc-960

BOM generated for controller: scu5

✓ What You'll Achieve

After completing this guide, wired to your SCU5 C(x)D controller with width data available over Industrial Ethernet for your PLC.

Estimated time: ~2–3 hours

☐ What You Need

Prerequisites

Sensor size selection: Single sensor: sensing range must exceed max web width + wander. Dual sensor: each sensor covers its respective edge + wander. If no single sensor is wide enough, use dual sensor.

SCU5 Output Options

The "+" is the analog-output option — it adds a live analog signal of the width value on top of the model's base capability, so a single controller can drive more than one output at once.

ModelOutputs
SCU5 C(x)DIndustrial Ethernet width data (overall width, left/right edge, centerline — loggable)
SCU5 C(x)D+Industrial Ethernet width data, plus an analog output of the width value

1 Install the Sensor

Edge-based web width measurement always uses free span mounting (web unsupported between rollers). Install the sensor so that the length of the sensor is parallel to the cross-machine direction (the width direction of the web).

Dual Sensor Installation: For dual-sensor width measurement, mount both sensors with the same camera orientation (facing the same direction). Then set their electronic orientation so that, relative to the web, one sensor tracks the left edge and the other tracks the right edge — see Sensor Installation Recommendations for orientation details.

Dual Sensor Setup

  • Position the left sensor to see the left edge, right sensor to see the right edge
  • Critical: mount both with the same camera (physical) orientation, but set their electronic orientation oppositely — the left sensor tracks the left edge, the right sensor the right edge
  • Each sensor needs margin for the full range of web widths (min to max) plus wander
  • Sensors do not need to be the same size — select each based on wander range at its edge
Light source: Infrared (IR) — default for most materials.

Reference Documents

2 Wire the System

Same sensor wiring as analog, plus Ethernet cable.

  1. Sensor: Connect Quick Disconnect Sensor Cable (U2-01975) from ODC Family sensor to SCU5 port S1 (and S2 for dual)
  2. Power: Connect 24 V DC Input Power Cable (21218-5m) to SCU5 port P1
  3. Ethernet: Connect M12 to RJ45S, Shielded Cable (21222-3m) from SCU5 Port 3 to PLC or network switch
Dual Sensor Wiring: Connect second sensor cable to controller port S2.

3 Configure & Verify

Web width measurement computes the distance between the detected left and right edges. The controller computes the width internally and provides the value directly.

Dual Sensor Width

Two sensors — one per edge — with the controller computing total width including the distance between sensors. Use when the web is wider than any single sensor. Not available for 1DC.

  1. Set each sensor's electronic orientation first — left sensor → left edge, right sensor → right edge — then perform single-sensor configuration for each
  2. Teach offset: place a known-width sample so both sensors see their edges
  3. Enter the known width value and press the Teach Offset button
  4. The controller computes the distance between sensors and stores it
  5. Optionally perform teach correction after teach offset for better repeatability
Teach offset = one-time during installation (re-teach only when sensors are physically moved). Teach correction = optional per product change. Final width = raw measurement + offset + correction.
What success looks like: Both sensors show green indicators, width reflects the full web width, changing products produces the expected width change.

Common Configuration Mistakes

  • Not re-teaching correction after product change — measurements drift with a different material
  • Forgetting teach offset — width will be wildly incorrect (missing distance between sensors)

View full configuration documentation

4 PLC Integration

The controller provides computed web width (with offset and correction applied) in dedicated registers. No PLC-side computation needed unless you prefer raw measurements.

  • Width is provided as a 16-bit register value with offset and correction applied
  • Raw edge positions (left and right) also available for PLC-side computation
  • For PLC-based tolerance monitoring: read width register, compare against nominal ± tolerance
  • Rockwell AOI handles pixel-to-mm conversion and bit unpacking automatically

📄 The register map, EDS file (EtherNet/IP), and Add-on Instruction (AOI) for Studio 5000 are in the Your Products section above — grouped on the product card with everything else you need to download.

+ Go Further

Related Quick Start Guides

Learn More

Need Help?

Email: experts@r2r.tech
Phone: +1-888-290-3215